Bradford Factor

Compute 2D - MultiWall model Usage------ rs_amp = multiwall_model(TXpoint , RXpoint , walls , material , [L0] , [n]); Inputs------- TXpoint Transmitter points (2 x Nt)RXpoint Receiver points (2 x Nr)walls Walls (4 x nwall) where [xi,0 ; yi,0 ; xi,1 ; yi,1] are coordinates of the i'th wall, i =...

The file calculates and plots FM noise sidebands for a carrier. It also does sinusoidal modulation. This simple way of adding noise to a carrier is useful for simulation of PLLs. It turns out, though, that the mean of the randn function is not as close to zero as it could be, and this causes the...

This function gives the decimation matrix which after post mulitpling it with the given signal gives the downsampled version of the original signal...D = decimmtx(x,N)decimates the given signal by a factor of N.[D,y] = decimmtx(x,N)gives D as well as the decimated signal y


Platforms: Matlab

The signals presented here can be used in demonstrating how the signal varies when the operation is made on either independent variable or dependent variable. The parameters can be varied to have a feel of the variation.Example(1): rect(1,2) plots the rectangular signal of amplitude 1 and a width...


Platforms: Matlab

The main program is Main_sound_and_vibs.m. Up to 100 metrics are for each of sound, hand arm vibrations, whole body vibrations, and motion sickness. Main_sound_and_vibs calls the primary depedent function"Continuous_Sound_and_Vibrations_Analysis" which contains the switch statement controlling...


Platforms: Matlab

Same functionality as the MATLAB rref function, but quicker.>> mex_rref_demo A = rand(200); R1 = rref(A);Elapsed time is 1.435837 seconds. R2 = mex_rref(A);Elapsed time is 0.012729 seconds. max(max(abs(R1 - R2))): 0Speed-up factor: 113


Platforms: Matlab

ScaleTime - fast linear matrix interpolationI have recorded timeseries of e.g. size [100'000 x 10] and cut out chunks of about 100 frames according to some events and normalize them to exactly 100 frames.For this task, the direct approach with Matlab's INTERP1 works, but it is slow:...


Platforms: Matlab

You only have to run main01.m, is easy to change the composition and operating conditions. If you want to add new components just add the critical propeties and acentric factor. Also is possible to use binary interaction parameters differents to zero.


Platforms: Matlab

The model simulates a three phase Sinusoidal PWM rectifier. Applied Voltage, switching frequency and sampling factor can be changed from the model properties block.


Platforms: Matlab

View factor is a MATLAB function that uses the CDIF (contour double integral formula) to calculates view factors between planar surfaces(polygons), no matter what are the shape and the orientation of the two figures.All you need to enter is the coordinates of the vertices that define the outlines...


Platforms: Matlab

Exercises and case studies for a rigorous approach to risk- and portfolio-management. This booklet stems from the review sessions of the six-day ARPM bootcamp.Contents include:Advanced multivariate statistics; copula-marginal decompositionAnnualization/projection (FFT, cumulants,...


Platforms: Matlab

We use the SRK equation of state to compute the correction factor due to gas-phase nonideality as a result of the high pressure applied in the ammonia synthesis. We also compute the extent of reaction. Plots of these two quantities versus pressure for temperature equal to 800K are presented. The...


Platforms: Matlab

Implementation based on:"Finite-Element Discretization Of Static Hamilton-Jacobi Equations Based On A Local Variational Principle"by F. Bornemann and C. RaschComments:1. There is no restriction on the type of triangulation, i.e. it does not need to be acute. But the method will require more than...


Platforms: Matlab

after downloadingto run program, enter damping(r,R,h,l,m)m=mass of bobh=height to which bob is thrownl=damping factor(i.e gamma=(l/2m))r=length of pendulmr=radius of bobenter ur values...for programm..enjoy...


Platforms: Matlab

y = units(x,'unit1','unit2') - Converts x from physical unit1 to unit2example: units(1,'in','mm') = 25.4The following units are supported:Acceleration: m/s^2, cm/s^2, mm/s^2, ft/s^2, in/s^2, GAngle: rad, deg, revArea: km^2, m^2, cm^2, mm^2, ym^2 (square-micrometer), sq-mile, sq-yd, sq-ft, sq-in,...


Platforms: Matlab

Simple function to calculate melt rates in meter water equivalent per year for a digital elevation model (DEM) based on positive degree days factor (PDD) using seasonal variation.User can specify factors: mean annual temperature, PDD_ice, seasonal variation in degrees and year length.Approach...


Platforms: Matlab

Value-at-Risk calculation for portfolio stocks using variance-covariance, historical and MonteCarlo methods. Portfolio can be larger as you want including either the risk factor (stock index, currency, etc.)


Platforms: Matlab

According to Wludyka and Nelson (1997), the Analysis of Means (ANOM), which is a test of location, can be converted into a test of scale and used to test the homogeneity of variances test, when the normality assumption is reasonable.The analysis of means for variances (ANOMV) is used for testing...


Platforms: Matlab

The training input vectors and target vectors are read from files data1in and data1out respectively. The no of nodes in input and output layer is decided depending on the no. of rows in these datasets.The no of hidden layers, No of nodes in each hidden layer and the target error (put 0.1) is to...


Platforms: Matlab

The code is explained in the article P. Okunev, "A Fast Algorithm for Computing Expected Loan Portfolio Tranche Loss in the Gaussian Factor Model", LBNL-57676, 2005.http://www-library.lbl.gov/docs/LBNL/576/7.../LBNL-57676.pdfFuther refinments of this algorithm are descibed in Okunev, Pavel,...


Platforms: Matlab