Ambient Temperature Sensor

wmalms monitors data obtained from a sensor chip: temperature, fan speed, voltage. It can be used as a dockable/swallowed applet with Window Maker, BlackBox and clones (incl. FluxBox), or any window manager that supports swallowing, including gnome, kde(kpanel)-1, fvwm and clones....

wmacpimon is an ACPI Temperature Monitor, a Windowmaker dockapp that monitors the temperature and Speedstep features in new ACPI-based systems. It supports batteries, automatic shutdown when the power is low, and multiple screens. Whats New in This Release: - All system was rewritten -...

System Health Monitor for Linux is a handy python program that will setup your system to generate RRD Graphs of network interface traffic, system load, memory usage, disk space and inode usage and graphs of the number of running processes. System Health Monitor features a user-friendly...


Platforms: *nix

QKtemp project is a program that records temperature data for RRDtool from the serial port. QKtemp records temperature data from the Qkits.com VK011 temperature interface into an RRD database, allowing you to graph temperature over time easily. The VK011 is a serial-port powered module with...


Platforms: *nix

EmiFreq applet is an daemon that shows/control the CPU frequency and temperature thanks to the cpufreq sysfs kernel interface. The emifreqd daemon enables the applet to change the cpu speed. The GUI is very clean, intuitive fast access to frequency change (with HIG help). Modelled over the...


Platforms: *nix

If you use Linux with WindowMaker and have a Dell 8XXX Laptop, installed the i8kutils and like some nice DockApps then try this one. wmi8k monitores the CPU temperature and the fan speed. Whats New in This Release: - By clicking on F R and F L you can now control the fans! (Switch fom off...


Platforms: *nix

Temperature Coversion Solution, convert Farenhiet, Celcius, Wind Chill and Heat Index


Platforms: Windows

Kima is a KDE kicker applet that shows the current CPU temperature and frequency. Make sure you have enabled the temperature ACPI kernel module (thermal.ko). Installation: run configure ./configure --prefix=$(kde-config --prefix) build the sources make install the applet (with...


Platforms: *nix

Temperature Monitor is an application to read out all available temperature sensors in Macintosh computers. The program can display and visualize measured values in a large variety of fashions. The application supports the following operations on the measured readings: display in a default window...


Platforms: Mac

A free conversion utility that will allow you to convert the most popular units of acceleration, angle, distance, temperature, volume


Platforms: Windows

audiospectrum is a very simple quartz screensaver that reacts to ambient audio. It's simple as possible to keep processor load and heat minimal. This is the good one, in my opinion, the screenshot really doesn't do it justice.Click the 'More Information' link on this page for all the other...


Platforms: Mac

WMtemp is based on code from (WMMemLoad and the sensor code is inspired by WMgtemp). It displays the CPU temperature and the system temperature in a dockapp, these temperatures are obtained through lm_sensors. The layout is in line with WMMemLoad and WMCPULoad (and a couple of others)....


Platforms: *nix

acpitail project shows in a tail-like way information off the battery-state, fan-states, temperatures, etc. of an ACPI capable system (mostly laptops). Screendump: laptop:/home/folkert/acpitail-0.1# ./acpitail -A 2 Mon Jun 18 15:28:45 2007 BAT0 remaining capacity: 99% (0 minutes) Adapter...


Platforms: *nix

wmacpi_temp is a Window Maker dock application that reads the temperature file in /proc/acpi in ACPI enabled kernels. In short, it displays the temperature of the processor, updated every minute (in Celsius or Fahrenheit). Installation: 1. make 2. su 3. make install (to put it in...


Platforms: *nix

Monitors CPU Temperature from command line in Fahrenheit and Celsius and gives results of highest and lowest temperatures, and average over period of time run, then logs the data. Requires ACPI.


Platforms: Mac

Tilt Mania is a little arcade game I wrote which uses the sudden motion sensor (SMS) of modern apple laptops. It's similar to BubbleGym in that it uses the computer itself as an input device, however it is freeware.Play by tilting your computer. Big scores are good. Low scores are bad. Get big...


Platforms: Mac

Gatotray project is a colorful tray icon to watch over CPU status including usage, frequency and temperature..


Platforms: *nix

heatload is a tool for Linux which plots the CPU load against the CPU temperature as measured by the ACPI subsystem. Installation: As this package is made with the GNU autotools you should run ./configure inside the distribution directory for configuring the source tree. After that you should...


Platforms: *nix

TrollBridge is a set of scripts that allows you to build a custom network authentication system that will capture unauthorized clients, direct them to a login page, and then redirect them to their original destination. It is based on the firewall script from NoCatSplash, but is written in python...


Platforms: *nix

wmhdplop project monitors your hard drives and displays visual information about their activity (read, write, swapin, swapout), and optionally (if hddtemp is running as a daemon), displays their temperature/status..


Platforms: *nix