Packets

Libnet is a high-level API (toolkit) allowing the application programmer to construct and inject network packets. It provides a portable and simplified interface for low-level network packet shaping, handling and injection. Libnet hides much of the tedium of packet creation from the application...

ARPSpoofDetector performs active and passive detection of ARP spoofing and IP (IPv4) address collision. The program can send healing packets with regular ARP information. ARPSpoofDetector is new GPL project initialized by NetMasters.CZ customers (specially 100MEGA Distribution). We didnt find...

Icmpenum sends ICMP traffic to potential targets on a network. Introduction: Host enumeration is the act of determining the IP address of potential targets on a network. This can be done in both layer 2 and layer 3. Icmpenum sends ICMP traffic for such enumeration. The ICMP packets supported...


Platforms: *nix

DNS Blacklist Packet Filter project is a Linux netfilter client that decides whether to accept or drop packets based on the results of a DNS blacklist query (such as MAPS, SORBS, or SPEWS, to name a few). One use is to filter all incoming SMTP SYN packets for spam filtering..


Platforms: *nix

"echoping" is a small program to test (approximatively) performances of a remote host by sending it TCP "echo" (or other protocol) packets. To install it, see the INSTALL file. Or type "./configure && make && sudo make install" if youre in a hurry :-) Several operating systems have echoping...


Platforms: *nix

ISIC is a suite of utilities to exercise the stability of an IP Stack and its component stacks (TCP, UDP, ICMP et. al.). It generates piles of pseudo random packets of the target protocol. The packets be given tendancies to conform to. Ie 50% of the packets generated can have IP Options. 25% of...


Platforms: *nix

Snort project is a "lightweight" intrusion detection technology in comparison to commercially available systems. Snort really isnt very hard to use, but there are a lot of command line options to play with, and its not always obvious which ones go together well. This file aims to make using...


Platforms: *nix

DHCPsql projects implements the RFC2132 and at least RFC3046 as a dynamic configurable SQL-based DHCP server, based on the udhcpd code, extended to mask-and-select by client DHCP packets. Targets: - Discover, start with a working pre prototype, always send first ip in subnet - Leases, SQL...


Platforms: *nix

HttpCapture is a core wrapper around the packet-capture library pcap and a framework for building plugins to filter, analyse, or display interesting network packets. The core of the application is minimal, and a collection of plugin libraries are used to actually process the packets. The...


Platforms: *nix

Xastir ptoject can receive and plot APRS position packets. Development is a collaborative effort of programmers from around the world. Xastir supports many map formats and is highly customizable. Check out the "Screen Shots" link to see just a few of the ways that Xastir can be used. Xastir...


Platforms: *nix

NetPacket::ARP is a Perl module to assemble and disassemble ARP (Address Resolution Protocol) packets. SYNOPSIS use NetPacket::ARP; $tcp_obj = NetPacket::ARP->decode($raw_pkt); $tcp_pkt = NetPacket::ARP->encode(params...); # Not implemented NetPacket::ARP provides a set of routines for...


Platforms: *nix

NetPacket::Ethernet is a Perl module to assemble and disassemble ethernet packets. SYNOPSIS use NetPacket::Ethernet; $eth_obj = NetPacket::Ethernet->decode($raw_pkt); $eth_pkt = NetPacket::Ethernet->encode(params...); # Not implemented $eth_data = NetPacket::Ethernet::strip($raw_pkt);...


Platforms: *nix

NetPacket::ICMP is a Perl module to assemble and disassemble ICMP (Internet Control Message Protocol) packets. SYNOPSIS use NetPacket::ICMP; $icmp_obj = NetPacket::ICMP->decode($raw_pkt); $icmp_pkt = NetPacket::ICMP->encode(); $icmp_data = NetPacket::ICMP::strip($raw_pkt);...


Platforms: *nix

etPacket::IGMP is a Perl module to assemble and disassemble IGMP (Internet Group Mangement Protocol) packets. SYNOPSIS use NetPacket::IGMP; $igmp_obj = NetPacket::IGMP->decode($raw_pkt); $igmp_pkt = NetPacket::IGMP->encode(params...); # Not implemented $igmp_data =...


Platforms: *nix

NetPacket::UDP is a Perl module to assemble and disassemble UDP (User Datagram Protocol) packets. SYNOPSIS use NetPacket::UDP; $udp_obj = NetPacket::UDP->decode($raw_pkt); $udp_pkt = NetPacket::UDP->encode($ip_obj); $udp_data = NetPacket::UDP::strip($raw_pkt); NetPacket::UDP provides a...


Platforms: *nix

NetPacket::TCP is a Perl module to assemble and disassemble TCP (Transmission Control Protocol) packets. SYNOPSIS use NetPacket::TCP; $tcp_obj = NetPacket::TCP->decode($raw_pkt); $tcp_pkt = NetPacket::TCP->encode($ip_pkt); $tcp_data = NetPacket::TCP::strip($raw_pkt); NetPacket::TCP...


Platforms: *nix

SYNOPSIS use NetPacket::IP; $ip_obj = NetPacket::IP->decode($raw_pkt); $ip_pkt = NetPacket::IP->encode($ip_obj); $ip_data = NetPacket::IP::strip($raw_pkt); NetPacket::IP provides a set of routines for assembling and disassembling packets using IP (Internet Protocol). Methods...


Platforms: *nix

pcap2c converts a pcap capture file (such as one from Ethereal/Wireshark or tcpdump) into a C source file, where the packets are stored as unsigned char arrays. These packets can then be compiled into a C program where they can be easily used for further manipulation, retransmission, etc....


Platforms: *nix

Apt-get Install / Remove Packet is a tool to install/remove packets with debian apt-get. About Apt-Get: Advanced Packaging Tool, or APT, is a package management system used by Debian and its derivatives. APT was originally designed to work with .deb packages on Debian systems, but it has...


Platforms: *nix

modttl modifies the TTL (time to live) of outgoing packets.


Platforms: Mac