Normal Cpu Temperature

Temperature Monitor features Real Time Temperature Display and will Display in the Temperature Box on the Top Left Corner of Software Interface. It works in conjunction with TEMPer GOLD hardware which is a usb device. The Action of Operation will Display on the Top Right Corner. There are Two...

Overclocks Helper is a small proggie simply to assist people in voiding their warranties. It displays CPU and bus clock speed. CPU temperature coming soon.

The Linux Duracell CPU load monitor is a program that drives a Duracell or Energizer on-battery tester to display the CPU load of a system. It can be easily adapted to display other things that can use a slow bar graph kind of display that varies between 0% and 100%. Instructions to hack a...


Platforms: *nix

WMsensors.pl is a small perl-program which monitors the temperature and voltages of CPU and motherboard and also shows the Fan-speed. Runs as a dock app for Window Maker. Needs no config-file, but a proper configured installation of lm_sensors and uses the Wharf::JDockApp modul from the CPAN..


Platforms: *nix

CPU Director allows you to view and configure the cache and processor clock speed settings on your PowerLogix upgrade card. The included utilities allow you to enable or disable the cache "on the fly", change the speed at which your backside cache operates and automatically enable the cache at...


Platforms: Mac

wmsupermon project is a universal monitoring dockapp. It can be used to monitor CPU usage, disk I/O, memory usage, swap, filesystems, space utilization, network traffic, wireless link quality, CPU frequency, CPU temperature, fan speed, voltages (without requiring lm_sensors), battery status...


Platforms: *nix

Linux ATI CPU HDD Control Daemon is able to reduce power consumption in a laptop by scaling back CPU, GPU (Radeon only), and HDD. It uses CPUFreq, ACPI, HDDTemp, and internal functions. It also checks for thermal overheating for the sake of laptop health. Now implementing an app scheduling...


Platforms: *nix

wmalms monitors data obtained from a sensor chip: temperature, fan speed, voltage. It can be used as a dockable/swallowed applet with Window Maker, BlackBox and clones (incl. FluxBox), or any window manager that supports swallowing, including gnome, kde(kpanel)-1, fvwm and clones....


Platforms: *nix

Clean Karamba CPU is a clean and simple, font is included. Monitors: - Cpu type - Speed - Cache - Temp - Load If there are problems please post them, so i can make a better version.. Download KDE-Look.org Community Portal for KDE Themes Wallpapers Icons Sounds Screenshots Schemes Skins...


Platforms: *nix

miniStat2 is a most powerful system monitoring widget, that allows you to measure almost everything in hardware of your Mac. The widget has one main view that shows summary info about your computer, and 6 dedicated panels with more detailed stats. The miniStat2 is not just a simple widget, it's...


Platforms: Mac

If you use Linux with WindowMaker and have a Dell 8XXX Laptop, installed the i8kutils and like some nice DockApps then try this one. wmi8k monitores the CPU temperature and the fan speed. Whats New in This Release: - By clicking on F R and F L you can now control the fans! (Switch fom off...


Platforms: *nix

EmiFreq applet is an daemon that shows/control the CPU frequency and temperature thanks to the cpufreq sysfs kernel interface. The emifreqd daemon enables the applet to change the cpu speed. The GUI is very clean, intuitive fast access to frequency change (with HIG help). Modelled over the...


Platforms: *nix

Kima is a KDE kicker applet that shows the current CPU temperature and frequency. Make sure you have enabled the temperature ACPI kernel module (thermal.ko). Installation: run configure ./configure --prefix=$(kde-config --prefix) build the sources make install the applet (with...


Platforms: *nix

Temperature Coversion Solution, convert Farenhiet, Celcius, Wind Chill and Heat Index


Platforms: Windows

Temperature Monitor is an application to read out all available temperature sensors in Macintosh computers. The program can display and visualize measured values in a large variety of fashions. The application supports the following operations on the measured readings: display in a default window...


Platforms: Mac

WMtemp is based on code from (WMMemLoad and the sensor code is inspired by WMgtemp). It displays the CPU temperature and the system temperature in a dockapp, these temperatures are obtained through lm_sensors. The layout is in line with WMMemLoad and WMCPULoad (and a couple of others)....


Platforms: *nix

Turn a bunch of average photos into stunning images with various actions and effects in a few clicks! Make color corrections to photos by adjust brightness, contrast, saturation, temperature, and tint. Improve visual quality of images through sharpening, noise reduction, and auto-white-balance...


Platforms: Windows

Monitors CPU Temperature from command line in Fahrenheit and Celsius and gives results of highest and lowest temperatures, and average over period of time run, then logs the data. Requires ACPI.


Platforms: Mac

mrtg-select allows the flexible display of MRTG graphs, chosen by keyword and time span. I use MRTG to graph all kinds of stuff, and looking at those graphs on the same page helps me detect correlations. ("Say, Professor -- that spike in CPU temperature came right when the Rapture Index hit a...


Platforms: *nix

Tgauge displays lm_sensor readings with gauge-style graphics on GNOME or ROX panels or in a window. Tgauge is a tool for displaying lm_sensors readings. Instead of boring old numbers, tgauge uses graphical representations designed to look like the gauges on a car dashboard. Or anything else if...


Platforms: *nix