Moneyline Host Lou

SID-IDS is a host intrusion detection system. Shell/PTY Intrusion Detection: Aims at detecting unwanted PTY action on UNIX systems. SID-IDS is a Host Intrusion Detection System. Consists of a kernel part and a user part. The kernel part plugs into terminal processing subsystem and logs hashed...

IP-Atlas tries to plot your location or any other host on the internet using the NetGeo data. It finds the latitude and longitude coordinates of the host and plots it on an image for you.It finds the latitude and longitude coordinates of the host and plots it on an image for you. You can try the...

PHREL is a per host rate limiter. PHREL will track the rate of incoming traffic to a server and insert a rule into IPTables when a configured threshold is crossed. The inserted chain may either rate limit or block the offending host for a period of time..


Platforms: *nix

ipcalc project takes an IP address and netmask and calculates the resulting broadcast, network, Cisco wildcard mask, and host range. By giving a second netmask, you can design subnets and supernets. It is also intended to be a teaching tool and presents the subnetting results as...


Platforms: *nix

SekHost is a host based firewall and packet prioritization utility for Linux systems. The configuration is simple yet powerful functionality is available. Installation of sekhost is very straightforward and actually only requires 2 things; the sekhost script itself, which is in the src...


Platforms: *nix

ImSafe (Immune Security For your Enterprise) is a host-based intrusion detection tool. After a learning phase, it is able to detect changes in processes behavior, to detect buffer overflows, etc. It is implemented through a device driver (as a kernel patch) for the Linux kernel, but can also be...


Platforms: *nix

ICMPInfo is a tool that uses ICMP type 13 and 17 to retrieve the current time of a remote host and its netmask.. Luigi Auriemma


Platforms: *nix

pmping provides a parallel multiple host ping with audible results (beep on the PC speaker). pmping is a script that pings multiple hosts in parallel and gives audible results depending on host state. The sounds come from the internal PC speaker, thus not needing a sound card. It beeps when a...


Platforms: *nix

NACE is a generic query engine used to automatically create host and service definitions for hosts on the network. It is intended to be used in a shell script at regular intervals by an experienced Nagios administrator to perform a query against the supplied host list. It then creates host and...


Platforms: *nix

httptype is a program that returns the http host software of a website. It is written in Perl. httptype reads a list of http hosts and optionally the port number for each of these. It queries each host, displaying the type of HTTP server running on that host. It reads the http_proxy and...


Platforms: *nix

Host enumeration is the act of determining the IP address of potential targets on a network. This can be done in both layer 2 and layer 3. Icmpenum project can send ICMP traffic for such enumeration. The ICMP packets supported are: Echo, Timestamp, Information and Netmask. Furthermore, it...


Platforms: *nix

Saint Jude software is a Project to develop Kernel-Level IDS mechinisms to protect the integrity of host systems. This will permit the discovery of local and remote root exploits during the exploit itself. Once discovered, Saint Jude will terminate the execution, preventing the root exploit...


Platforms: *nix

"echoping" is a small program to test (approximatively) performances of a remote host by sending it TCP "echo" (or other protocol) packets. To install it, see the INSTALL file. Or type "./configure && make && sudo make install" if youre in a hurry :-) Several operating systems have echoping...


Platforms: *nix

netAI comes from Network Traffic based Application Identification and has been developed for identifying the end host applications that are responsible for traffic flows in the network. Unlike previous solutions that identify the application based on port numbers or packet payload (either...


Platforms: *nix

Argo is a extensible, simple framework for controling a host running multiple Xen instances. Argo is a monitoring system for the Xen hyperviser, comprised of a network server which runs upon your Xen host and any number of clients which connect to that server over a socket. The monitoring...


Platforms: *nix

THC-Probe is the ultimate host scanner compilation for Linux, featuring nmap, snmpscan, netbios auditing tool and super-cool vh shell script. INSTALL: just run "make install". Everything will be installed in /usr/local RUN: just run "netprobe" and see the options. Every host scanned will be...


Platforms: *nix

Node Director project is a system management application for centralized user and host management in small to medium sized Unix / Linux / (Windows) system environments..


Platforms: *nix

With WAppFTP_Client3 you can transfer Files from your local system to a remote host (Unix or Windows 2000/NT), or from a remote Host to your local system. You will be able to create directories, delete directories/files, change the name of directories/files and show Files (a simple Editor is...


Platforms: *nix

VSTi Host allows VST plugins to be used outside of larger host applications (like Cubase, Logic, etc.). It also allows for sequencers that may not have native support for VST plugins and/or instruments (like ProTools, Logic 6, Vision, Digital Performer, and Metro for example) to use them, as long...


Platforms: Mac

The LightScribe host software enables your system to use LightScribe.Important!: Please use this LightScribe Host Software 1.4.105.1 with LaCie LightScribe Labeler 1.2 for Mac exclusively. Donlt use it with previous versions of LaCie LightScribe Labeler for MacNote: Users with LaCie DVD...


Platforms: Mac