ICMPScan 1.1

ICMPScan scans the specified address, or addresses, for ICMP responses. Usage: icmpscan [ -EPTSNMAIRcvbn ] [ -A address ] [ -f filename ] [ -i interface ] [ -r retries ] [ -t timeout ] target [...] Options: -i, --interface Listen on the specified interface. If unspecified, icmpscan will examine the routing table and select the most appropriate interface for each target address. -c, --promisc Put in interface into promiscuous mode. As this option increases the load on the system in general, it should only be used if spoofing of source packets address is enabled with the "-A" option. -A, --address Specify the source IP address of generated packets. -t, --timeout Specify the timeout, in milli-seconds, before retrying. -r, --retries Specify the number of attempts to elicit a particular ICMP response. -f, --file Read target list from the specified file. -E, -P, --echo, --ping Check of ICMP Echo responses. -T, -S, --timestamp Check for ICMP Timestamp responses. -N, -M, --netmask Check for ICMP Netmask responses. -I, --info Check for ICMP Info responses. -R, --router Check for ICMP Router Solicitation responses. -v, --verbose Increase the output verbosity. -B, --debug Target Specification The simplest case is listing single hostnames or IP addresses on the command line. If you want to scan a subnet of IP addresses, you can append /mask to the hostname or IP address. mask must be between 0 (scan the whole Internet) and 32 (scan the single host specified). Use /24 to scan a class "C" address and /16 for a class "B". There is also a more powerful notation which lets you specify an IP address using lists/ranges for each element. Thus you can scan the whole class "B" network 192.168.*.* by specifying "192.168.*.*" or "192.168.0-255.0-255" or even "192.168.1-50,51-255.1,2,3,4,5-255". And of course you can use the mask notation: "192.168.0.0/16". These are all equivalent. If you use asterisks ("*"), remember that most shells require you to escape them with back slashes or protect them with quotes. Examples: The following example checks the first 16 addresses in the 192.168.1.0/24 netblock for all ICMP responses. The scan speed is increased by lowering the timeout value and setting the number of retries to 1: > icmpscan -t 500 -r 1 192.168.1.0-16 192.168.1.0: Echo (From 192.168.1.17!) 192.168.1.0: Address Mask [255.255.255.0] (From 192.168.1.17!) 192.168.1.7: Echo 192.168.1.7: Timestamp [0x03ab2db0, 0x02d4c507, 0x02d4c507] 192.168.1.7: Address Mask [255.255.255.0] 192.168.1.8: Echo 192.168.1.8: Address Mask [255.255.255.0] To display failed probes, increase the output verbosity: > icmpscan -v 192.168.1.1 192.168.1.1: -- No response to Echo request -- 192.168.1.1: -- No response to Timestamp request -- 192.168.1.1: -- No response to Netmask request -- 192.168.1.1: -- No response to Info request -- 192.168.1.1: -- No response to Router Solicitation request -- Individual ICMP types can be checked for by listing their corresponding flags on the command line: > icmpscan -v --echo --netmask 192.168.1.7 192.168.1.7: Echo 192.168.1.7: Address Mask [255.255.255.0]. Does what is says on the tin: Scans the specified address, or addresses, for ICMP responses.

Requirements:	No special requirements
Platforms:	Linux
Keyword:	Address,  Address Mask,  Addresses,  Check For,  Icmpscan,  Ip,  Networking,  No Response,  Response,  Responses,  Scan,  Specified,  System
Users rating:	0/10