Wireless Sniff

KriptPass is a simple generator of general purpose user passwords and hexadecimal keys for wireless encryption. KriptPass project is actually a GUI for makepasswd, a utility (c)1997-1999 by Rob Levin. In order to run KriptPass youll need makepasswd and kommander..

wmwave is dockapp for window maker to display statistical information about a current wireless ethernet connection. Installation: Unzip the the distribution tar xvfz wmwave-0-4.tgz Change directories cd wmwave Say make and then install the program and manpage by make install...

This is a Linux driver for wireless LAN cards based on Intersils Prism2/2.5/3 chipset. The driver supports a so called Host AP mode, i.e., it takes care of IEEE 802.11 management functions in the host computer and acts as an access point. This does not require any special firmware for the...


Platforms: *nix

KWirelessMonitor is a small KDE application that docks into the system tray and monitors the wireless network interface. It supports both Linux (tested on several major distributions) and FreeBSD (tested on 5.2.1). I wrote this because I like the compactness of the Wavelan/Orinoco monitor in...


Platforms: *nix

KWaveControl is a tool for wireless devices and it is based on the wireless extensions. KWaveControl runs under Linux with KDE and docks into the panel. The tray icon in the panel shows you the current link quality and bitrate. The main window indicates information about the device, where you...


Platforms: *nix

SNMP::Info::Layer3::Aironet is a Perl5 Interface to Cisco Aironet Wireless Devices running Aironet software, not IOS. SYNOPSIS # Let SNMP::Info determine the correct subclass for you. my $aironet = new SNMP::Info( AutoSpecify => 1, Debug => 1, # These arguments are passed directly on to...


Platforms: *nix

Kismet application is an 802.11 layer2 wireless network detector, sniffer, and intrusion detection system. Kismet will work with any wireless card which supports raw monitoring (rfmon) mode, and can sniff 802.11b, 802.11a, and 802.11g traffic. Kismet identifies networks by passively collecting...


Platforms: *nix

wlan-ui is a very small Linux GUI tool for connecting to wireless networks. It is written in perl, and is a basic example of using perl with Gtk and Glade. There is also some simple process handling (forking off a process, collecting output, killing the process if cancelled).. Linux, wireless,...


Platforms: *nix

MAPI is a general API for interfacing with any wireless device driver that support wireless extensions. It is based on the wireless extensions and Wireless Tools. The current version of the API can be used to get most of the information provided by the wireless tools (iwspy, iwconfig, iwpriv.)...


Platforms: *nix

MWavelan is a kernel network device driver for the WaveLAN/IEEE wireless network card, which supports signal strength reading from all the access points in range, plus some more features. All three drivers lack the ability to provide the signal strength measurement from all the access points...


Platforms: *nix

p54u is a reverse engineered driver for USB Prism54 SoftMAC wireless devices with the ISL3880, ISL3886, and GW3887 chipsets. p54u project supports many of the USB adapters sold nowadays. Whats New in This Release: - This release adds FreeBSD 6 support, a new firmware upload scheme (at last,...


Platforms: *nix

NetworkControl is a utility to control and monitor network interfaces, including wireless ones (for which you see a signal strength meter, as shown). NetworkControl addresses a conspicuous lack in most Linux distributions — most tend to be short on easy-to-use network utilities, even...


Platforms: *nix

KWifiSelector is a KDE tool to display all available wireless networks (WLAN). For each of them, the parameters (such as IP configuration and WEP keys) can be configured. KWifiSelector also allows the user to connect to and disconnect from a selected network. Whats New in This Release: -...


Platforms: *nix

giwconfig is graphical user interface which displays information about a wireless (WiFi) network interface. Whats New in This Release: - The program now scans for a wireless interface on startup instead of using a hardcoded interface..


Platforms: *nix

ad-tolk enables Wi-Fi enabled machines that are within range of each other to automatically setup their wireless interfaces by calculating IP addresses based on their MAC addresses (in the range 10.0.0.0/8) and joining an ad-hoc cell called "livefolio". Afterward, all nodes can discover their...


Platforms: *nix

Wireless Access Point Utilites for Unix is a set of utilites to configure and monitor Wireless Access Points under Unix using SNMP protocol. Utilites knownly compiles by GCC and IBM C compiler and run under Linux, FreeBSD, NetBSD, MacOS-X, AIX, QNX, OpenBSD. Utilites writen by Roman Festchook...


Platforms: *nix

Sleek Monitor is a combination of basic monitors for: - OS - KDE - Kernel - CPU & cache - GPU & GPU Temp - Memory - Wired & Wireless networks - battery with time - date and calendar. Sleek Monitor KDE-Look.org Community Portal for KDE Themes Wallpapers Icons Sounds Screenshots Schemes...


Platforms: *nix

wificontrol project is a Kommander script that simply allows you to activate or deactivate the wireless module on your laptop. Only works if using the acerhk module. Must be run as root (perhaps with kdesu). wificontrol KDE-Apps.org Community Portal for KDE Applications Software Office...


Platforms: *nix

With the application KWiFiManager you can configure and monitor your wireless LAN PC-Cards under Linux/KDE. The application is made for KDE version 3.x only. The simplest way to compile this package is: 1. `cd to the directory containing the packages source code and type `./configure to...


Platforms: *nix

OSWA-Assistant is a self-contained, freely downloadable, wireless-auditing toolkit for both IT-security professionals and End-users alike. This toolkit is our contribution to the wireless security/auditing community and, as the "Assistant" moniker implies, and is designed for the following...


Platforms: *nix