Voltage Multiplier

The model simulates space vector based three phase inverter with the state space model of thefilter. The model parameters such as frequency, switching frequency, load parameters, voltage, modulation index and filter A,B,C,D parameters.

A simple simulation Model for DC DC step-down buck converter, the model allows measurments of output current/voltage, capacitor current, diode current. Ripples in each measurment can be observed very accurately using the scope

The model simulates three phase three level diode clamped inverter using sinosoidal pulse width modulation. FFT analysis of output voltage is performed using power GUI. Switching frequency and output frequency can be adjusted using the initilzing callback function in the model properties.


Platforms: Matlab

The model simulates a three phase Sinusoidal PWM rectifier. Applied Voltage, switching frequency and sampling factor can be changed from the model properties block.


Platforms: Matlab

Given a set of customer requirements, design a suitable DC/DC converter.Project includes full derivation of control transfer functions, simulink model.Design Spec:Voltage input200-650 VDCVoltage output28VDC, regulatedFull load power300WMinimums load20% of full loadRipple voltage?100mV at full...


Platforms: Matlab

This model simulates three phase inverter. Sawtooth waveform has been used as the carrier. Triplen of level 1/6 of reference were injected in the reference to utilize the maximum DC link voltage. The output voltage range increases by injecting the triplen harmonics in the reference provided that...


Platforms: Matlab

The model simulates buck converter using different approaches. Parameters can be change from the initializing callback function in the model properties. First circuit implements buck using a MOSFET and diode, second implements using two MOSFETs and third implements using the model equation. Power...


Platforms: Matlab

This software has been realized by Bret Fortenberry at the CNS Technology Lab at Boston University (http://techlab.bu.edu/). A model to show the properties of EPSPs and IPSPs in the postsynaptic cell. The model allows a user to adjust the number of EPSP and IPSP inputs, the rise and fall times...


Platforms: Matlab

Find the projection of point P in R^n on the ellipsoidE = { x = x0 + U*(z.*radii) : |z| = 1 }, where U is orthogonal matrix of the orientation of E, radii are the axis lengths, and x0 is the center.Or on generalized conic E = { x : x'*A*x + b'*x + c = 0 }.The projection is the minimization...


Platforms: Matlab

This is a Simulink Model Code of a guinea-pig ventricular action potential published byFaber GM, Silva J, Livshitz L, Rudy Y. Kinetic properties of the cardiac L-type Ca2+ channel and its role in myocyte electrophysiology: a theoretical investigation.Biophys J. 2007 92:1522-1543.The action...


Platforms: Matlab

This project aims to demonstrate speed control of aDC series motor. It involves the use of armature voltage control,to control the speed of the motor. The speed of the motor iscontrolled for a typical speed profile of a washing machine. ThePID controller of the motor is optimized for a good...


Platforms: Matlab

The model simulates buck converter using different approaches. Parameters can be change from the initializing callback function in the model properties. First circuit implements buck using a MOSFET and diode, second implements using two MOSFETs and third implements using the model equation. Power...


Platforms: Matlab

This script calculates and/or reports the following approximate values for each real- or integer-valued active column: * Minimum * Q1 (first quartile) * Median * Q3 (third quartile) * Maximum * Q1 * x*IQR * Q3 * x*IQR Where x is a user defined multiplier to define outlier thresholds...


Platforms: Mac

A capacitor is a device for storing charge. In this simulation, you can investigate a relatively simple capacitor, known as a parallel-plate capacitor. It consists of two identical metal plates, placed parallel to one another. The capacitor can be charged by connecting one plate to the positive...


Platforms: Mac

The EJS Electric Multipole Model of a point charge (monopole), a dipole, or a quadrupole can show either field vectors or the scalar potential (voltage). A slider changes the charge and a movable detector shows the electric field direction and magnitude or measures the potential. Detector values...


Platforms: Mac

The RLC Circuit with Function Generator model simulates a resistor, capacitor and inductor in series with either a sinusoidal or square wave voltage source and plots the time dependence of the voltage drops across each element. Users can vary the resistance, capacitance, inductance and source...


Platforms: Mac

Wmsensormon is a doc app for WindowMaker that utilizes lm_sensors to monitor CPU temp, sys temp, fan speeds, and cpu voltage. It offers configurable warnings for over heating, and the sensors displayed are adjustible by the user with command line param


Platforms: *nix

This page has news, information, documentation and links software for the sysstat utilities that I created for Linux. The sysstat utilities are a collection of performance monitoring tools for Linux. These include sar, sadf, mpstat, iostat, nfsiostat, cifsiostat, pidstat and sa tools. Go to the...


Platforms: *nix

The k6mult utility sets the CPU multiplier factor on AMD K6-III+ and K6-2+ processors featuring AMD PowerNow(tm). The CPU clock speed is determined by multiplying this factor by the Front Side Bus (FSB) speed. You should use the k6mult utility if you want to increase the multiplier factor after...


Platforms: *nix

k10ctl is an AMD Family 10h (aka K10) P-State, frequency and voltage modification utility . Its main purpose is overclocking and / or "undervolting" the CPU and to configure Cool'n'Quiet settings.


Platforms: *nix